Have questions or want to discuss cycling? Join Now or Sign In to participate in the BikeRide community.

New: Take Part in the March Giveaway: Coming Soon 3/24


Chain skip
#1
I've  a 9speed DA that is fine going up & down the gearing, but put a load on 1st, 2nd & sometime, the chain skips. I cannot get my indexing right to get rid of it, any thoughts?
  Reply
#2
Most common cause of this is worn chain and rear gear cluster (cassette).
You can measure for chain stretch and visually inspect cassette, but this kind of skipping can happen even before there is a huge amount of obvious wear on the parts. Usually recommended to replace both parts at the same time unless you have a strong reason to think only one is worn.
  Reply
#3
(10-09-2015, 12:42 PM)DaveM Wrote:  Most common cause of this is worn chain and rear gear cluster (cassette).
You can measure for chain stretch and visually inspect cassette, but this kind of skipping can happen even before there is a huge amount of obvious wear on the parts. Usually recommended to replace both parts at the same time unless you have a strong reason to think only one is worn.

+1

Other possibilities (less likely):
* a stiff link in the chain.
* inadequate chain lubrication.
* weak RD spring.
* chain too long.
Nigel
  Reply
#4
(10-09-2015, 02:19 PM)nfmisso Wrote:  
(10-09-2015, 12:42 PM)DaveM Wrote:  Most common cause of this is worn chain and rear gear cluster (cassette).
You can measure for chain stretch and visually inspect cassette, but this kind of skipping can happen even before there is a huge amount of obvious wear on the parts. Usually recommended to replace both parts at the same time unless you have a strong reason to think only one is worn.

+1

Other possibilities (less likely):
* a stiff link in the chain.
* inadequate chain lubrication.
* weak RD spring.
* chain too long.

Chain is new. Likely i didnt cut the length correctly, first time using a removable link chain. Or it is the cassete, it has about 3k mileson it?
  Reply
#5
Check the length first. But putting a new chain on an old cassette (even one without that many miles) is a very typical cause of the sudden appearance of chain skip under load. Chains and cassettes "wear into each other" and it's common to have problems when you change one but not the other.
  Reply
#6
(10-08-2015, 08:38 PM)mastermartymo Wrote:  I've  a 9speed DA that is fine going up & down the gearing, but put a load on 1st, 2nd & sometime, the chain skips. I cannot get my indexing right to get rid of it, any thoughts?

Maybe a dumb question but are you using a 9 speed chain? They are different then a ten 8 speed chain I'm told. Slightly thinner I believe.
"Where ever we go, there we are"
  Reply


Possibly Related Threads...
Thread
Author
Replies
Views
Last Post
 
13,549
04-04-2013, 10:44 PM
Last Post: larsonian
 
12,904
05-13-2012, 03:48 PM
Last Post: Joe_W
 
9,407
07-18-2011, 04:42 AM
Last Post: Joe_W
 
7,595
10-28-2008, 10:42 PM
Last Post: Alex Ramon

Forum Jump:

[-]
10 Latest Posts
What tools have you bought recently?
Yesterday 06:57 PM
Santini fluted frame
Yesterday 06:47 PM
Expensive bikes with crappy wheels
Yesterday 10:15 AM
Where are you from and What is your favo...
03-27-2024 11:43 PM
2007 Trek Pilot S.P.A. 5.2
03-27-2024 07:06 PM
2010 Specialized Hardrock
03-26-2024 09:16 PM
1990 Specialized Rockhopper How to Fluff...
03-25-2024 07:05 PM
Thread busted on right pedal crank
03-24-2024 08:52 PM
Trek domane tyre
03-24-2024 05:48 PM
Modern rims crack at spoke holes
03-24-2024 05:32 PM

[-]
Join BikeRide on Strava
Feel free to join if you are on Strava: www.strava.com/clubs/bikeridecom

[-]
Top 5 Posters This Month
no avatar 1. Painkiller
21 posts
no avatar 2. ReapThaWhirlwind
16 posts
no avatar 3. meamoantonio
15 posts
no avatar 4. Jesper
15 posts
no avatar 5. GirishH
15 posts