Bicycle TutorBicycle Tutor

Show off your bike!

Related video tutorials:
Gearing ratio far too light
#1
Folks
I'm looking for some advice
I have a boardman team c 2010 spec and I fond that I run out if gears on a descent.
The set up is as follows front and rear mechs SRAM rival rear is short gauge
Shimano hg 5600 10 SPd cassette 12-25.
Shimano hg5600 chain
Chainset is the SRAM gxp 50/34
And SRAM rival shifters
So what I'm looking to find out is a possible set up that's a bit more meaty
Any suggestions would be greatly appreciated
Reply
#2
I would try a bigger ring in the chainset. I have a 28/38/48 on my mountain bike. Most of the time I hear of people having 54 teeth in the front.
Reply
#3
you need to spec the maximum teeth your front derailluer can handle between rings
15 to 22 on most setups
53/39 for example
you should be running an 11t on the rear also
but remember you will probably have to replace your chain
There are two kinds of people in the world, "Those who help themselves to people, and those who help people!"
Reply
#4
As mentioned above, get a cassette with an 11t smallest sprocket.
http://www.sheldonbrown.com/k10.shtml#shimano9

The GXP is offered in 53/39.
http://www.sram.com/sram/road/products/s900-gxp-crankset
The Red group goes to 55/42
http://www.sram.com/sram/road/products/sram-red-crankset

I don't know the BCD, 130mm maybe ? Harris has 54T chainrings in 130mm BCD
http://sheldonbrown.com/harris/chainrings/130.html
and 110mm
http://sheldonbrown.com/harris/chainrings/110.html

See here for how to measure BCD:
http://sheldonbrown.com/harris/chainrings.html

53/11 is 15% taller than the 50/12 you currently have.
55/11 is 20% taller than the 50/12 you currently have.

You will need a new longer chain if you change the chain rings
Nigel
Reply
#5
Folks
Thanx a million for the advice
Looks like I've a little bit of work to do then
I'll let you know how I fare
Thanx
Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
  Changing/replacing a SR Suntour XCT light crankset rpesq 8 9,871 04-29-2015, 04:56 PM
Last Post: rpesq
  Gear Ratio AL_BUNDY 4 5,311 07-31-2012, 01:48 AM
Last Post: AL_BUNDY
  Gearing Suggestions Sparkie 3 4,548 11-07-2011, 11:55 PM
Last Post: Sparkie
  Cross Gearing - How Many Combos Are Bad? TopTube 4 7,722 07-07-2011, 05:00 PM
Last Post: Dan Malloy
  Chainrings needed for half-step plus granny gearing junoak04 5 6,812 08-29-2010, 05:13 AM
Last Post: junoak04
  Re-gearing Problem Barry 2 4,822 01-26-2009, 03:25 AM
Last Post: Barry
  Gearing Question wrightee 4 7,732 10-27-2008, 11:42 PM
Last Post: DaveM
  Gearing Question Guest 3 4,533 08-18-2008, 08:59 PM
Last Post: Alex Ramon

Forum Jump:



ISSN 1918-3445 © Copyright 2007-2010 Bicycle Tutor / Privacy Policy / Created by Alex Ramon

feed