Have questions or want to discuss cycling? Join Now or Sign In to participate in the BikeRide community.

New: Take Part in the March Giveaway: Coming Soon 3/24


Gt Chucker 2008 derailleur problem
#1
hi i have a gt chucker and when i change gears its noisy in every gear. also the chain slips off the front single sprocket when in to the high gears. and when i change down gears i have tried adjusting the screws on the derailleur but it makes no difference. any help would be good thanx. the only thing that has been changed is the back wheel. it has the same amount of cogs on the back wheel, so couldn't see why this would be the problem.

  Reply
#2
The screws are only for adjusting the end stops of the dérailleur to make sure it doesn't hit the spokes or run of the small cog.

There is a cable adjuster which is used for aligning up the dérailleur to cogs.

The adjuster is usually where the cable attaches to the dérailleur and sometimes there is one at the changer end.

Check out Alex's tutorial:-
http://bikeride.com/adjust-rear-derailleur/
http://bikeride.com/v/gfYw2Z0eAA
Ride hard or ride home alone!
  Reply
#3
Just to add on if your Front Derailleur still does the same check out this After:

http://bikeride.com/adjust-front-derailer/
http://bikeride.com/v/gfYw2aEiAA
Good maintenance to your Bike, can make it like the wheels are, true and smooth!
  Reply
#4
Chain dropping off the front could be:-

Teeth worn.
Worn or slack chain (to long or not enough tension)
Derailleur lost tension.

Also check that the derailleur is still straight. (vertical when viewed from the back and parallel with rear cogs when viewed from above.)
Ride hard or ride home alone!
  Reply
#5
I sorted the problem needed to change chain ring and adjust rear dérailleur i have another problem i put a sealed head set bearing in to the gt frame it was off a fold up bike frame it fits nicely but the steering feels a little tight and the more i tighten the center bolt the harder the steering is??
  Reply
#6
I think you have an "A-head" stem. Over-tightening the center bolt will make the steering stiff. The bolt should be just tight enough to take up any play in the bearings. The 2 screws at the back of the stem hold the steering together.

See Alex's tutorial:-
http://bikeride.com/adjust-threadless-headset/
http://bikeride.com/v/gfYw2aR_AA

Slacken the 2 screws and then adjust the top center bolt to take out any play. Then re-tighten the 2 rear bolts making sure the stem is in-line with the front tire. You may have to do this a couple of times until the new bearings are bedded in.
Ride hard or ride home alone!
  Reply


Possibly Related Threads...

Forum Jump:

[-]
10 Latest Posts
Santini fluted frame
Today 01:52 AM
2010 Specialized Hardrock
03-26-2024 09:16 PM
1990 Specialized Rockhopper How to Fluff...
03-25-2024 07:05 PM
Thread busted on right pedal crank
03-24-2024 08:52 PM
Trek domane tyre
03-24-2024 05:48 PM
Modern rims crack at spoke holes
03-24-2024 05:32 PM
Cup & Cone — Simple & Durable or PITA & ...
03-24-2024 04:53 PM
Falling back
03-24-2024 04:45 PM
Derailluer Hanger Alignment Tool
03-24-2024 02:51 PM
Chain sits on top of chainring when shif...
03-24-2024 02:41 PM

[-]
Join BikeRide on Strava
Feel free to join if you are on Strava: www.strava.com/clubs/bikeridecom

[-]
Top 5 Posters This Month
no avatar 1. Painkiller
20 posts
no avatar 2. ReapThaWhirlwind
16 posts
no avatar 3. Jesper
15 posts
no avatar 4. meamoantonio
15 posts
no avatar 5. GirishH
15 posts