Bicycle TutorBicycle Tutor

Show off your bike!

Related video tutorials:
Quick chain question
#1
I'm planning on making a century ride tomorrow on my converted SS and since the shop here doesn't have any 130mm single chainrings I decided to throw my old stock triple chainring back on my bike to give me a few more options if my legs get cranky. So I throw on the old chainring, put the chain on the middle ring, and throw it up on the trainer. It works fine. I take it off and head outside for a test and as soon as I start the chain starts making a popping sound and eventually pops the master link out and breaks the chain. Could it be that my single speed chain doesn't work with my triple chainring and just getting the other chain size will make it work or could something else be the culprit here?
Reply
#2
Was the chain the wider 1/8" size? Technically these can be used on 3/32" chainrings (which your triple is) but it does put a bit more stress on them. Note that you can't use a 3/32 chain on an 1/8 inch cog. So if your rear cog is 1/8, you have to use the wider chain.

How is the chain line with the triple crank? If it's badly off, that would also stress the chain.

Finally, may have just been coincidence or that you didn't get the chain rejoined properly when you adjusted it for the triple crank. Even with a master link, every time you "break" the chain it weakens it a bit making it more likely to actually break.
Reply
#3
Yeah the bike started out as 21spd road bike and I converted it to singlespeed and added singlespeed chainring,cog, and tensioner and went with the singlespeed chain. No matter if it is on the middle or largest chainring with the triple it makes a horribly bad popping sound back around the tensioner area and such every time I turn the cranks. It works smooth as butter with the singlespeed chainring I bought for the conversion but It is a 48t and I was going to go a little lighter since it will be my first century and supposed to be windy tomorrow.
Reply
#4
Hmmm, not sure what's up but "horribly bad popping sound" certainly isn't a good sign.
Note that single speed stuff can either be 1/8" or 3/32". Multi-speed is always 3/32.
The triple crank doesn't have biopace (oval) chainrings does it?

If you can't get a chainring, you could change the cog in back instead. Going one tooth less in the back will have a much bigger impact than one less in the front of course.
Reply
#5
dUH! Can't believe I didnt think of that. I have a 16t right now, is there a common setup that works with the 48t up front.
Reply
#6
You can use any common size cog in back, it just depends what gear ratio you want. Going to a 17 would give you a roughly 6% lower gear (1/16). Not huge, but noticeable. Roughly the same affect that switching to a 45 up front would achieve.
http://www.sheldonbrown.com/gears/
Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
  Quick Chain Link??'s !TREK4ME! 4 5,068 12-05-2015, 01:41 AM
Last Post: GeorgeET
  How to put the quick chain link together more quickly? SpeedBikeNut32 4 3,219 01-21-2015, 02:02 AM
Last Post: SpeedBikeNut32
  Question about chain length Jerry845 1 3,274 10-21-2014, 12:10 PM
Last Post: cny-man
  Chain question mtnbikr 2 3,667 02-09-2014, 05:33 PM
Last Post: cny-man
  Chain question swk3000 11 7,003 07-09-2012, 05:48 AM
Last Post: Joe_W
  Chain Line Question Dosninerguy 4 8,410 01-08-2010, 01:19 PM
Last Post: KDC1956
  Question about my bike chain frogprincessashlie 1 5,855 02-13-2009, 05:06 PM
Last Post: cyclerUK
  KMC X 10 Chain - Popped a Quick Link Aushiker 2 6,858 02-12-2009, 11:11 PM
Last Post: Aushiker

Forum Jump:



ISSN 1918-3445 © Copyright 2007-2010 Bicycle Tutor / Privacy Policy / Created by Alex Ramon

feed