Bicycle TutorBicycle Tutor

Show off your bike!

Related video tutorials:
Replacing Schwinn Tourist bottom bracket
#1
hello all,

I bought a Schwinn Tourist at Target a few months back and want to replace the bottom bracket. It is the cup/cone/bearing type. In short, can I use a sealed bottom bracket or must I stay with the cup/cone and bearing type? It is 68 X 127. I'm fairly certain (but not sure) that the TPI is 24. The spindle is square taper. I researched the spindle on the Sheldon Brown site (it is 3S) and it is actually 125 mm wide, but the "symmetrical equivalent" per his charts is 127.

I was looking at the shimano BB-UN55 and figured that one would fit based on my best evaluations. I'm also kind of leery of the plastic end on the shimano part. I've already learned my expensive lesson of buying a bike from target.

Any ideas?

On the other hand, if I should stick with the cup/bearing type, would there be a reasonably priced upgrade?

Any thoughts are appreciated! Thanks!
Reply
#2
(10-20-2011, 02:54 AM)mizzoudoc89 Wrote:  hello all,

I bought a Schwinn Tourist at Target a few months back and want to replace the bottom bracket. It is the cup/cone/bearing type. In short, can I use a sealed bottom bracket or must I stay with the cup/cone and bearing type? It is 68 X 127. I'm fairly certain (but not sure) that the TPI is 24. The spindle is square taper. I researched the spindle on the Sheldon Brown site (it is 3S) and it is actually 125 mm wide, but the "symmetrical equivalent" per his charts is 127.

I was looking at the shimano BB-UN55 and figured that one would fit based on my best evaluations. I'm also kind of leery of the plastic end on the shimano part. I've already learned my expensive lesson of buying a bike from target.

Any ideas?

On the other hand, if I should stick with the cup/bearing type, would there be a reasonably priced upgrade?

Any thoughts are appreciated! Thanks!

You can replace with a sealed bearing type - basically a throw away part, not serviceable, or keep the serviceable cup/bearing type. Do you mean UN54? http://www.amazon.com/Shimano-BB-UN54-Bottom-Bracket-127mm/dp/B0011ZCEHK/

The plastic end actually works better than metal in this application because the rigid bearing assembly needs some give in the part to prevent binding.

My preference is cups and seperate loose bearings (not caged); because it serviceable, stronger and stiffer than the alternatives. I use grease intended for boat trailer wheel bearings, due to low cost, very water resistant and works well.

I replace the balls whenever I service the BB. Proper tightening is critical.
Nigel
Reply
#3
(10-20-2011, 03:12 AM)nfmisso Wrote:  
(10-20-2011, 02:54 AM)mizzoudoc89 Wrote:  hello all,

I bought a Schwinn Tourist at Target a few months back and want to replace the bottom bracket. It is the cup/cone/bearing type. In short, can I use a sealed bottom bracket or must I stay with the cup/cone and bearing type? It is 68 X 127. I'm fairly certain (but not sure) that the TPI is 24. The spindle is square taper. I researched the spindle on the Sheldon Brown site (it is 3S) and it is actually 125 mm wide, but the "symmetrical equivalent" per his charts is 127.

I was looking at the shimano BB-UN55 and figured that one would fit based on my best evaluations. I'm also kind of leery of the plastic end on the shimano part. I've already learned my expensive lesson of buying a bike from target.

Any ideas?

On the other hand, if I should stick with the cup/bearing type, would there be a reasonably priced upgrade?

Any thoughts are appreciated! Thanks!

You can replace with a sealed bearing type - basically a throw away part, not serviceable, or keep the serviceable cup/bearing type. Do you mean UN54? http://www.amazon.com/Shimano-BB-UN54-Bottom-Bracket-127mm/dp/B0011ZCEHK/

The plastic end actually works better than metal in this application because the rigid bearing assembly needs some give in the part to prevent binding.

My preference is cups and seperate loose bearings (not caged); because it serviceable, stronger and stiffer than the alternatives. I use grease intended for boat trailer wheel bearings, due to low cost, very water resistant and works well.

I replace the balls whenever I service the BB. Proper tightening is critical.

Yes, that is the one I was looking at. Thanks for the correction. As well, I appreciate your insight. I suppose the reason I wanted to change/upgrade was because I had read (and have seemingly found) that the parts they use on that bike are bottom of the barrel. Moreover, I read somewhere on the net that the bearings that come on my bike wear out fast.

Perhaps the easiest thing to do would be just to replace the bearings....it would likely be cheaper too in the long run. Thanks for your tip on the grease too!
Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
  Replacing a bottom bracket on a Dahon coxen00 9 11,172 06-11-2017, 10:42 PM
Last Post: painkiller
  BMX Bottom Bracket Creaking and Clicking felpel102 2 4,204 10-15-2016, 08:36 PM
Last Post: GeorgeET
  Bottom bracket... Strange style I haven't seen before? Quixoticish 1 2,163 07-21-2016, 11:36 AM
Last Post: Joe_W
  No spindle in the bottom bracket? Jacomo 5 3,258 09-18-2015, 11:11 AM
Last Post: painkiller
  Shimano BB-UN26 bottom bracket torque specs Tranced 5 5,015 09-13-2015, 05:33 PM
Last Post: DaveM
  Help to identify and upgrade Huffy BB bottom bracket rpesq 3 3,522 09-04-2015, 04:35 PM
Last Post: DaveM
  Frozen bottom bracket on Katmando? elmore leonard 8 3,713 05-12-2015, 11:28 PM
Last Post: elmore leonard
  Crank bearing bottom bracket edge 4 3,700 05-08-2015, 10:56 PM
Last Post: edge
  German FAG bottom bracket Konstantin 3 3,824 02-23-2015, 10:41 PM
Last Post: Konstantin
  Bottom Bracket for a 1973 Schwinn Continental cvs1998 6 3,341 01-01-2015, 06:56 PM
Last Post: GeorgeET

Forum Jump:



ISSN 1918-3445 © Copyright 2007-2010 Bicycle Tutor / Privacy Policy / Created by Alex Ramon

feed