Bicycle TutorBicycle Tutor

Show off your bike!

Related video tutorials:
Rear wheel rubbing brake pad
#1
I'm new to the Forum and getting back on the pedals. I just purchased a Trials bike and after assembly and first ride, rear wheel became un-aligned and is rubbing against the brake. I noticed there are (2) bracket type parts, one on each side, that look like they attach to the frame at the rear forks. These are NOT attached to anything but sit around the axle. Any ideas on what this part is called and if it's the cause of my problem?

I appreciate the help.
Reply
#2
I think what you're talking about are called chain tensioners. If so, they help you adjust the position of the rear wheel in the frame. It may be that you didn't have them and the rear axle bolts tight enough to prevent slipping. Google chain tensioners to see if we're talking about the same thing and how to set them.

One note, align the wheel to the frame (center between the seat stays and chain stays) and make sure the chain is tight enough. THEN align the brake to the wheel. Don't use the brake to decide if the wheel is in the right place.
Reply
#3
(10-18-2011, 11:51 PM)DaveM Wrote:  I think what you're talking about are called chain tensioners. If so, they help you adjust the position of the rear wheel in the frame. It may be that you didn't have them and the rear axle bolts tight enough to prevent slipping. Google chain tensioners to see if we're talking about the same thing and how to set them.

One note, align the wheel to the frame (center between the seat stays and chain stays) and make sure the chain is tight enough. THEN align the brake to the wheel. Don't use the brake to decide if the wheel is in the right place.

Thanks. I'll look it up. And great tip on not using the break to align the wheel. That's excactly what I was doing.
Reply
#4
(10-18-2011, 11:51 PM)DaveM Wrote:  I think what you're talking about are called chain tensioners. If so, they help you adjust the position of the rear wheel in the frame. It may be that you didn't have them and the rear axle bolts tight enough to prevent slipping. Google chain tensioners to see if we're talking about the same thing and how to set them.

One note, align the wheel to the frame (center between the seat stays and chain stays) and make sure the chain is tight enough. THEN align the brake to the wheel. Don't use the brake to decide if the wheel is in the right place.

Here's a photo. It's the slotted aluminum part between the frame and hub. I see pre-drilled holes in the frame that would line up, but there's no way to get an allen wrench in there to attach or tighten it to the frame. Any suggestions or tricks of the trade that might help?
Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
  Schwinn Meridian Rear Wheel Bearings Tyro65 0 3,233 04-08-2017, 09:26 PM
Last Post: Tyro65
  Rear wheel noise - help please luckstar69 4 4,110 08-17-2016, 06:31 AM
Last Post: Sixty55
  What spoke lengths for rear wheel M529 and Rhyno Lite? TrailShredder 10 5,307 04-02-2016, 12:13 AM
Last Post: jtj
  Rear wheel keeps shifting NotRequired 1 3,132 04-01-2016, 11:13 PM
Last Post: jtj
  Replacing rear wheel after patching a flat munnikm 3 4,469 12-04-2015, 09:33 AM
Last Post: munnikm
  Rear Wheel Nuts won't screw in Pugceratops 3 3,481 08-11-2014, 03:35 PM
Last Post: nfmisso
  Rear wheel troubles Ben1981 3 3,399 08-01-2014, 07:46 PM
Last Post: Ben1981
  Rear hub replacement to disc brake type dexterdancer1 1 2,375 07-03-2014, 03:18 PM
Last Post: nfmisso
  Specialized Epic 29er rear wheel broken spoke DLH2014 5 5,471 03-19-2014, 03:47 PM
Last Post: Joe_W
  Mt. Fury Roadmaster 15 Speed Index Shifting Rear Wheel Problem devan264 4 6,353 03-17-2014, 11:53 AM
Last Post: cny-man

Forum Jump:



ISSN 1918-3445 © Copyright 2007-2010 Bicycle Tutor / Privacy Policy / Created by Alex Ramon

feed