Have questions or want to discuss cycling? Join Now or Sign In to participate in the BikeRide community.

New: Take Part in the March Giveaway: Coming Soon 3/24


Wheel hub bearings. Room for one more ball?
#1
Hi all.

Recently my bicycles wheel hubs are showing their age and need a proper servicing.

I have stripped down both wheel hubs and was surprised to notice that I could comfortably, without any steady handed trickery, fit two more bearings in the cup for my rear wheel hub and one more bearing in the the cups of my front wheel hub.

According to the Shimano tech document my rear hub takes nine 1/4 inch ball bearings per side and the front hub takes ten 3/16 inch balls per side.

Should I stick with what Shimano is saying or should I pack the cups with as many bearings as it can comfortably take???
  Reply
#2
You did get the correct ball size? (just asking)
It is normal that 1 additional ball might fit in (though usually it would be slightly too tight). If there's really room for one additional ball (and everything can be assembled as it should, check over locknut distance and orientation of axle) I probably would put it in.
  Reply
#3
typically if original bearing were caged, add one ball
There are two kinds of people in the world, "Those who help themselves to people, and those who help people!"
  Reply
#4
Nope, no caged, just loose in the cup.

I have since been advised by the LBS that it is normal for the cup to not be completely filled with bearings and to simply obide by the Shimano tech docs.
  Reply
#5
This last advice is standard for any loose ball cup and cone bearing.
DO NOT ADD EXTRA BALLS EVER over the OEM design. As others have said, a less than full fit is normal, and packing more balls in (even if they fit) screws up the bearing cone/cup geometry and ball circulation; and will lead to rapid failure. I found this out the hard way by packing an extra (25th) ball into the rh ball ring of a Sturmey Archer AW 3 speed...
cheers,
AW-hub.



(10-21-2011, 07:58 PM)d3v Wrote:  Nope, no caged, just loose in the cup.

I have since been advised by the LBS that it is normal for the cup to not be completely filled with bearings and to simply obide by the Shimano tech docs.
  Reply


Possibly Related Threads...
Thread
Author
Replies
Views
Last Post
 
2,743
02-07-2022, 02:46 PM
Last Post: Jesper
 
3,203
08-30-2021, 03:46 AM
Last Post: Poissonj1
 
18,996
05-26-2015, 02:31 PM
Last Post: eric1023
 
41,026
01-13-2015, 12:13 PM
Last Post: joseph wolf man
 
17,452
09-16-2014, 01:39 PM
Last Post: GeorgeET

Forum Jump:

[-]
10 Latest Posts
What tools have you bought recently?
Yesterday 06:57 PM
Santini fluted frame
Yesterday 06:47 PM
Expensive bikes with crappy wheels
Yesterday 10:15 AM
Where are you from and What is your favo...
03-27-2024 11:43 PM
2007 Trek Pilot S.P.A. 5.2
03-27-2024 07:06 PM
2010 Specialized Hardrock
03-26-2024 09:16 PM
1990 Specialized Rockhopper How to Fluff...
03-25-2024 07:05 PM
Thread busted on right pedal crank
03-24-2024 08:52 PM
Trek domane tyre
03-24-2024 05:48 PM
Modern rims crack at spoke holes
03-24-2024 05:32 PM

[-]
Join BikeRide on Strava
Feel free to join if you are on Strava: www.strava.com/clubs/bikeridecom

[-]
Top 5 Posters This Month
no avatar 1. Painkiller
21 posts
no avatar 2. ReapThaWhirlwind
16 posts
no avatar 3. GirishH
15 posts
no avatar 4. meamoantonio
15 posts
no avatar 5. Jesper
15 posts