Have questions or want to discuss cycling? Join Now or Sign In to participate in the BikeRide community.

New: Take Part in the March Giveaway: Coming Soon 3/24


Easton crank question
#1
I have a Specialized Sequoia Elite road bike. It came with 3 front gears.
Now, I want to switch and put an Easton crank with two gears. Will it work properly with the current 9 gear derailleur in the back? Will I have problems shifting gears and chain jumping out of gear?
Thanks
  Reply
#2
The back: yes. The front: no. You need to change the left hand shifter and maybe the front dérailleur (depending on the tooth count of the new chain rings).
  Reply
#3
(02-11-2013, 02:42 AM)Joe_W Wrote:  The back: yes. The front: no. You need to change the left hand shifter and maybe the front dérailleur (depending on the tooth count of the new chain rings).

Joe, thanks for the reply. Here's the thing, the Easton crank comes with two gears. The high and the low gear in the front will each work fine with each of the gears in the back AS LONG as I do not shift. When I try to shift the chain will jump out completely at times. I tried adjusting the two screws but can't seem to get a perfect balance so that I may shift back and forth. Is this why you suggest I change the left shifter?

Thanks
  Reply
#4
To me it sounds as if the front dérailleur overshifts quite a bit. If you would very carefully shift only one click it should work, though. The rear dérailleur should be able to cope with the tooth difference on the crank set, the one you had before likely was bigger.

Which "two screws" were you trying to adjust?
  Reply
#5
I can't tell if you having trouble with the chain falling off on the triple crank or on the new Easton crank. One thing to check is the alignment (height and angle compared to the chainrings.) If these are off, it is difficult to get the front der adjusted right no matter how much you play with the limit screws. If you're using your old der on the new crank, it might perform better with a front der designed for double chainring cranks. They are a bit different than those designed for triple. But there's no rule that says you have to swap it out.

I think you can actually keep your old shifter. But you'll have to be aware that it will have an extra shift position that goes to nothing. The limits should keep the derailleur from moving, but you'll need to keep track of keeping the shifter out of the defunct position.

One question of course is "why" change the crank? What are you trying to achieve?
  Reply
#6
Joe, Dave, thanks again. I found that I reduced the weight by almost 1 lb while removing an unnecessary gear, which means simplifying the shifting. BTW, I followed the advice of adjusting the front der. and so far it seems to have worked while shifting only once on the left side.
thanks both
  Reply


Possibly Related Threads...
Thread
Author
Replies
Views
Last Post
 
27,941
07-19-2021, 12:00 AM
Last Post: rbx
 
8,879
08-24-2010, 04:46 AM
Last Post: trevgbb

Forum Jump:

[-]
10 Latest Posts
Santini fluted frame
Today 01:39 PM
Expensive bikes with crappy wheels
Today 10:15 AM
Where are you from and What is your favo...
Yesterday 11:43 PM
2007 Trek Pilot S.P.A. 5.2
Yesterday 07:06 PM
2010 Specialized Hardrock
03-26-2024 09:16 PM
1990 Specialized Rockhopper How to Fluff...
03-25-2024 07:05 PM
Thread busted on right pedal crank
03-24-2024 08:52 PM
Trek domane tyre
03-24-2024 05:48 PM
Modern rims crack at spoke holes
03-24-2024 05:32 PM
Cup & Cone — Simple & Durable or PITA & ...
03-24-2024 04:53 PM

[-]
Join BikeRide on Strava
Feel free to join if you are on Strava: www.strava.com/clubs/bikeridecom

[-]
Top 5 Posters This Month
no avatar 1. Painkiller
21 posts
no avatar 2. ReapThaWhirlwind
16 posts
no avatar 3. Jesper
16 posts
no avatar 4. GirishH
15 posts
no avatar 5. meamoantonio
15 posts