Bicycle TutorBicycle Tutor

Show off your bike!

Related video tutorials:
How to Adjust Your Front Derailleur How to Adjust Your Front Derailleur
* Now with 3D interactive instructions
Can't shift highest and lower gear
#1
Hi, I have problem with my rear derailleur.
I just build bike with groupset shimano 105 5700(with new cable). the problem is rear derailleur cant move from hardest gear(smallest gear) to second gear. but if I shifting from hardest to easy gears like 2 or 3 click time the chain just start move to second gear.
if I shifting again to the next gear until 10 shifting click, the chain just stop on the 9th gear. can't move to hardest gear(10th gear).

and if I shifting going back to the hardest gear/smallest gear, they will stop at second gear(2nd of smallest gear).

does anybody know what's actually happened in this problem?
sorry if my words are hard to understand.
thanks
Reply
#2
(06-08-2014, 11:40 AM)rabany Wrote:  Hi, I have problem with my rear derailleur.
I just build bike with groupset shimano 105 5700(with new cable). the problem is rear derailleur cant move from hardest gear(smallest gear) to second gear. but if I shifting from hardest to easy gears like 2 or 3 click time the chain just start move to second gear.
if I shifting again to the next gear until 10 shifting click, the chain just stop on the 9th gear. can't move to hardest gear(10th gear).

and if I shifting going back to the hardest gear/smallest gear, they will stop at second gear(2nd of smallest gear).

does anybody know what's actually happened in this problem?
sorry if my words are hard to understand.
thanks

sounds like your H/L limit screws are not set proper, and your cable tension is not correct. Also check for binding with your cable/housing.
There are two kinds of people in the world, "Those who help themselves to people, and those who help people!"
Reply
#3
You have more than one problem, and you need to follow the correct procedure for installation and adjustment. Installing and adjusting a drive train is not a matter of just attaching things. Videos here are supposed to be good, but I always recommend reading and understanding written procedures first. Google "install rear derailleur" do the same search for "shift cable" instead, and you can also try 'adjust" instead of "install." The parktool.com/blog and sheldonbrown.com results are usually the most accurate and helpful.

If the derailleur can get to the large/small cogs at all the problem is not primarily the limit screws. Cables seat in after the 1st few shifts, so that the cable is slack until you shift a few clicks - so likely the cable needs to be retightened, then the derailleur adjusted. A spring in the derailleur must pull the cable through the housing to allow the shift to the small cog, so if it is slow or stubborn getting there you probably have too much friction in the cable/housing - multiple causes - kinks, poor cutting of the ends, no ferrules, poor housing length, etc.
Reply
#4
(06-08-2014, 02:07 PM)cny-man Wrote:  You have more than one problem, and you need to follow the correct procedure for installation and adjustment. Installing and adjusting a drive train is not a matter of just attaching things. Videos here are supposed to be good, but I always recommend reading and understanding written procedures first. Google "install rear derailleur" do the same search for "shift cable" instead, and you can also try 'adjust" instead of "install." The parktool.com/blog and sheldonbrown.com results are usually the most accurate and helpful.

If the derailleur can get to the large/small cogs at all the problem is not primarily the limit screws. Cables seat in after the 1st few shifts, so that the cable is slack until you shift a few clicks - so likely the cable needs to be retightened, then the derailleur adjusted. A spring in the derailleur must pull the cable through the housing to allow the shift to the small cog, so if it is slow or stubborn getting there you probably have too much friction in the cable/housing - multiple causes - kinks, poor cutting of the ends, no ferrules, poor housing length, etc.

thanks alot dude. I appreciate it. might be my outer cable ends is not cut properly.
(06-08-2014, 01:43 PM)painkiller Wrote:  
(06-08-2014, 11:40 AM)rabany Wrote:  Hi, I have problem with my rear derailleur.
I just build bike with groupset shimano 105 5700(with new cable). the problem is rear derailleur cant move from hardest gear(smallest gear) to second gear. but if I shifting from hardest to easy gears like 2 or 3 click time the chain just start move to second gear.
if I shifting again to the next gear until 10 shifting click, the chain just stop on the 9th gear. can't move to hardest gear(10th gear).

and if I shifting going back to the hardest gear/smallest gear, they will stop at second gear(2nd of smallest gear).

does anybody know what's actually happened in this problem?
sorry if my words are hard to understand.
thanks

sounds like your H/L limit screws are not set proper, and your cable tension is not correct. Also check for binding with your cable/housing.

thanks alot dude, might be the problem is the outer cable ends is not cut properly.
Reply
#5
(06-10-2014, 10:12 AM)rabany Wrote:  
(06-08-2014, 02:07 PM)cny-man Wrote:  You have more than one problem, and you need to follow the correct procedure for installation and adjustment. Installing and adjusting a drive train is not a matter of just attaching things. Videos here are supposed to be good, but I always recommend reading and understanding written procedures first. Google "install rear derailleur" do the same search for "shift cable" instead, and you can also try 'adjust" instead of "install." The parktool.com/blog and sheldonbrown.com results are usually the most accurate and helpful.

If the derailleur can get to the large/small cogs at all the problem is not primarily the limit screws. Cables seat in after the 1st few shifts, so that the cable is slack until you shift a few clicks - so likely the cable needs to be retightened, then the derailleur adjusted. A spring in the derailleur must pull the cable through the housing to allow the shift to the small cog, so if it is slow or stubborn getting there you probably have too much friction in the cable/housing - multiple causes - kinks, poor cutting of the ends, no ferrules, poor housing length, etc.

thanks alot dude. I appreciate it. might be my outer cable ends is not cut properly.
(06-08-2014, 01:43 PM)painkiller Wrote:  
(06-08-2014, 11:40 AM)rabany Wrote:  Hi, I have problem with my rear derailleur.
I just build bike with groupset shimano 105 5700(with new cable). the problem is rear derailleur cant move from hardest gear(smallest gear) to second gear. but if I shifting from hardest to easy gears like 2 or 3 click time the chain just start move to second gear.
if I shifting again to the next gear until 10 shifting click, the chain just stop on the 9th gear. can't move to hardest gear(10th gear).

and if I shifting going back to the hardest gear/smallest gear, they will stop at second gear(2nd of smallest gear).

does anybody know what's actually happened in this problem?
sorry if my words are hard to understand.
thanks

sounds like your H/L limit screws are not set proper, and your cable tension is not correct. Also check for binding with your cable/housing.

thanks alot dude, might be the problem is the outer cable ends is not cut properly.

make sure to change only one thing at a time. outer cable end length is most irrelevant if it attaches adequately to the RDR tension screw.
set limit screws (front, then rear), then test. if still a problem, then work on cable tension with the barrel adjuster or by manually adding more tension on the cable itself.
Reply
#6
Thanks for your input Sean. people for the most part do not realize that cutting a housing is not a true finish to the housing. I find that a cut-off wheel with a square cut thru the housing does a great job. the type from a Dremmel type tool is great!
There are two kinds of people in the world, "Those who help themselves to people, and those who help people!"
Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
  Front derailleur won't shift into third (largest) gear bruin1989 1 6,852 08-01-2016, 07:14 AM
Last Post: Joe_W
  Need to press twice to get to lower clog dude 2 4,001 05-13-2016, 04:39 PM
Last Post: DaveM
  Failure to shift from 4th to 5th gear BillDare 2 5,627 12-26-2015, 09:11 PM
Last Post: BillDare
  I can only use the highest 5 gears on my 8spd rear cog bianchi29er 21 20,309 09-01-2014, 09:35 AM
Last Post: wikey
  Gear shift lever replacement. packman126 2 3,554 08-23-2014, 12:20 AM
Last Post: packman126
  Takes ages to shift up a gear jrstevenson1987 3 3,442 07-21-2014, 02:26 AM
Last Post: cny-man
  Stuck gear shift on Next womens 18 speed robynfla133 1 4,158 05-11-2014, 03:41 PM
Last Post: nfmisso
  Rear derailleur problem, chain rubbing the lower pulley cage grandmaster 15 18,365 03-19-2014, 02:54 AM
Last Post: grandmaster
  Front gear shift stopped working... zeusthunder 4 7,477 05-27-2013, 06:32 PM
Last Post: haykong
  Left gear shift not working jadefrog 7 12,051 03-12-2013, 10:58 AM
Last Post: painkiller

Forum Jump:



ISSN 1918-3445 © Copyright 2007-2010 Bicycle Tutor / Privacy Policy / Created by Alex Ramon

feed