Bicycle TutorBicycle Tutor

Show off your bike!

Related video tutorials:
How do you adjust the brake cant on old caliper bikes?
#1
I'm trying to fix up an older bike. The brake cant on the front tire, right side is way off. It's already destroyed the break pad. I need to figure out how to change the cant, or any new brake pads I install will be destroyed in similar fashion. How exactly do you do this?

http://imageshack.com/a/img661/9351/fFDYSx.jpg
http://imageshack.com/a/img538/8725/StqwyG.jpg
http://imageshack.com/a/img674/3443/D3pKIS.jpg
http://imageshack.com/a/img540/3103/bjkNzF.jpg
Reply
#2
I would first determine if the binder bolt is bent, if it is i would just buy a new brakeset if you like the bike and save yourself the trouble. In the one pic showing the back by the spring it appears to have been bent as the spring curl should not touch. fix that first and the pad will start to come around. you will have to take it apart to do this. a dead blow or brass hammer will not dent or damage the arm. reassemble and fine tune the arm around the pad area using a cresent wrench or two to finish.
There are two kinds of people in the world, "Those who help themselves to people, and those who help people!"
Reply
#3
Painkiller is right, the left arm (left when you're on the bike) of the caliper is bent back slightly. You can do one of a few things here.
- Take the caliper apart and bend that arm back straight.
- Leave it bent but bend the tab that holds the brake pad so it is parallel to the rim.
- Replace the whole caliper

In general, this type of brake is pretty tuff and you can bend them around some without a problem. But there's always a risk something was stressed too far and the whole thing could snap. There's no way we can tell you for sure. So safest is to replace, but unless I saw some other evidence of damage, I would bend the arm back into place.

Note that if the brakes squeal a lot, try bending the pad flange so that the front of the pad hits the rims a mm or 2 before the back of the pad. That usually gets rid of brake squeal.
Reply
#4
First, I tried to bend it back while attached to the bike. After that, I took the brake assembly apart, took the caliper arm down to the side walk outside, and hit it with a hammer for several minutes. Failing that, I put the brake assembly back together and had another idea. I took the break pad off and put a large, sturdy, screwdriver in the opening and gave it a hard twist. Finally it bent back into place! Amazing what a little leverage can do. I could have saved myself a lot of trouble had I just done that from the very beginning. On the bright side, I now have an excellent understanding of how caliper brakes work. Now I can replace the disintegrating brake pads without worrying about the brakes not connecting with the rims correctly. Thanks for all the advice!
Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
  Side pull caliper brakes malfunctioning? Psylock1045 6 6,431 05-04-2015, 06:22 PM
Last Post: DaveM
  Newbie rider needs front caliper fleetwood 1 3,026 11-05-2014, 12:38 AM
Last Post: nfmisso
  Adjust diacompe dp7 bbxrider 4 4,691 05-15-2012, 06:19 AM
Last Post: bbxrider
  Adjust sidepull child's first hand brake Stompper3 9 23,517 11-30-2011, 02:45 AM
Last Post: toniok
  Single pivot caliper brake help magicmayonaise 11 15,066 08-13-2011, 02:08 PM
Last Post: magicmayonaise
  Hydraulic Brake Caliper Problem Jordan300 5 9,114 10-25-2010, 01:49 AM
Last Post: Jordan300
  Replacing cheapo plastic mountain bike caliper brake systems sablewing 9 16,882 09-09-2010, 02:47 AM
Last Post: Robb
  Improving side pull caliper brakes Bikeshrink 2 7,299 08-22-2010, 05:43 PM
Last Post: DaveM
  Reconditioning Side pull caliper brakes Skyguy9999 1 7,551 07-23-2010, 10:49 PM
Last Post: DaveM
  Sidepull Caliper brakes problem oddjobkebab 4 10,796 06-21-2010, 06:44 AM
Last Post: Joe_W

Forum Jump:



ISSN 1918-3445 © Copyright 2007-2010 Bicycle Tutor / Privacy Policy / Created by Alex Ramon

feed