Bicycle TutorBicycle Tutor

Show off your bike!

Related video tutorials:
Side pull caliper brakes malfunctioning?
#1
I am attempting to replace the brakes on my bicycle, and I have a set of side-pull caliper brakes. When I took them apart, they worked just fine. But putting them back together, I cannot get them to function properly...the arms are both pulling up, and pulling the entire brake assembly to one side, instead of squeezing together as they should. What in the world is going on? I put it back together exactly the same way as I took it apart...it doesn't make sense!
Reply
#2
(04-29-2015, 11:10 AM)Psylock1045 Wrote:  I am attempting to replace the brakes on my bicycle, and I have a set of side-pull caliper brakes. When I took them apart, they worked just fine. But putting them back together, I cannot get them to function properly...the arms are both pulling up, and pulling the entire brake assembly to one side, instead of squeezing together as they should. What in the world is going on? I put it back together exactly the same way as I took it apart...it doesn't make sense!

You may have them tightened them down too much?
"Where ever we go, there we are"
Reply
#3
what kind of side pull caliper brakes?  Pictures are most helpful, brand and model are also useful.
Nigel
Reply
#4
https://youtu.be/LKmgvt4aQqI

took a quick video of what issues I'm having. I thought I had it figured out but I still can't get them to work quite right. Stressing out because I need this bike ready to roll by Wednesday morning, and this is seriously causing a headache. Been working on these stupid brakes for at least 5 days.
Reply
#5
Looks like you have several other issues with the bike besides the brakes.  

The rear wheel bearings need to be adjusted - should be taken apart, inspect the cups and cones, if good, pack with grease and replace the balls.  

There is a reason that single pivot side pull brakes are not used anymore except on the cheapest of bikes - they are not easy to keep working reliably.  Make sure that you have all the washers oriented in the correct direction so that the die roll does not cause one are or the other to hang up.  Make sure you are not missing a thin washer (maybe metal or plastic).  Do not over tighten.  Use a lubricant compatible with the materials used in the brake - this is important - a lubricant that degrades the plastic parts will result in a sticking brake.  Use only soap and water to clean the parts - solvents may degrade the plastic parts resulting in a sticking brake.
Nigel
Reply
#6
(05-04-2015, 04:12 PM)nfmisso Wrote:  Looks like you have several other issues with the bike besides the brakes.  

The rear wheel bearings need to be adjusted - should be taken apart, inspect the cups and cones, if good, pack with grease and replace the balls.  

There is a reason that single pivot side pull brakes are not used anymore except on the cheapest of bikes - they are not easy to keep working reliably.  Make sure that you have all the washers oriented in the correct direction so that the die roll does not cause one are or the other to hang up.  Make sure you are not missing a thin washer (maybe metal or plastic).  Do not over tighten.  Use a lubricant compatible with the materials used in the brake - this is important - a lubricant that degrades the plastic parts will result in a sticking brake.  Use only soap and water to clean the parts - solvents may degrade the plastic parts resulting in a sticking brake.

yeah, I know I gotta get that taken care of, just don't have the time or funds at the moment. The bike will function fine for now and I'll get it worked on asap. As for the more problematic issue of the brakes, that is all just basic maintenance, any answer to getting them to work properly? I tried to fix them how I saw in a video tutorial, but they don't want to work for me like they did in the video. I can't seem to "center" them, and keep getting 1 arm doing more work than the other.
Reply
#7
Pure speculation, but it could be that the whole caliper assembly is just off center. One way to fix this is to loosen the nut on the back that holds the caliper to the bike, center the caliper, and then retighten. The trick is that when you tighten the nut, it tends to twist the whole caliper around. One other technique is to put a flat screw driver tip against the spring on the caliper and give it a couple light taps with a hammer. Sometimes this will rotate the caliper to center.
Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
  Newbie rider needs front caliper fleetwood 1 2,828 11-05-2014, 12:38 AM
Last Post: nfmisso
  How do you adjust the brake cant on old caliper bikes? Chimoshi 3 2,347 10-29-2014, 04:07 PM
Last Post: Chimoshi
  I disassembled my dual pivot side-pull and can't put it back together! Karamazovs 6 4,470 03-20-2014, 07:17 AM
Last Post: Karamazovs
  One side of V brake doesn't spring back jpm1983 26 128,039 01-03-2014, 02:02 AM
Last Post: sleepytyn
  Linear Pull brake help gofasts-10 6 7,485 09-23-2013, 12:49 AM
Last Post: docB
  Hydralic disc brake lever pull Adrian888 2 4,937 08-30-2013, 05:21 AM
Last Post: Adrian888
  Center Pull and Side Pull Bill 2 6,170 11-12-2012, 01:43 PM
Last Post: Bill
  Replacing cantilever brakes with linear pull brakes Sparky 2 10,744 01-23-2012, 09:21 PM
Last Post: nfmisso
  Linear pull brakes? Newb question shadowz85 1 4,516 09-07-2011, 06:37 PM
Last Post: DaveM
  Single pivot caliper brake help magicmayonaise 11 14,555 08-13-2011, 02:08 PM
Last Post: magicmayonaise

Forum Jump:



ISSN 1918-3445 © Copyright 2007-2010 Bicycle Tutor / Privacy Policy / Created by Alex Ramon

feed