Bicycle TutorBicycle Tutor

Show off your bike!

Related video tutorials:
How to Adjust Your Front Derailleur How to Adjust Your Front Derailleur
* Now with 3D interactive instructions
Single-speed to 8x geared conversion shifter problem
#1
Hi all
new to the site; I'm sure this is something that has come up before, but I'm currently trying to do a single-speed to 8x geared conversion, with a downtube shifter.
I've got the dropdown hanger for the rear derailleur bolted into the drop-out (after reading advice from this site...thanks!), and the rear derailleur mounted.

The chain runs through the derailleur and smallest gear (and the front cassette) fine, and I've attached the cable into the derailleur OK. The derailleur adjusts position when I use the shifter, but the chain doesn't move with it. I can manually move the chain onto the biggest sprocket, but not currently using the shifter.  I've tried tightening the cable, but am not 100% sure what the starting position of the shifter should be (I've not found much on Youtube for this) and have double-checked I've routed the cable through the shifter properly (using parktool guide).  I'm officially stumped.

Does that make any sense? If so, does anyone have any advice? I can provide a photo if it helps. Any/ all suggestions welcome!

Cheers
T
Reply
#2
(01-16-2016, 11:39 AM)Tomtebi Wrote:  Hi all
new to the site; I'm sure this is something that has come up before, but I'm currently trying to do a single-speed to 8x geared conversion, with a downtube shifter.
I've got the dropdown hanger for the rear derailleur bolted into the drop-out (after reading advice from this site...thanks!), and the rear derailleur mounted.

The chain runs through the derailleur and smallest gear (and the front cassette) fine, and I've attached the cable into the derailleur OK. The derailleur adjusts position when I use the shifter, but the chain doesn't move with it. I can manually move the chain onto the biggest sprocket, but not currently using the shifter.  I've tried tightening the cable, but am not 100% sure what the starting position of the shifter should be (I've not found much on Youtube for this) and have double-checked I've routed the cable through the shifter properly (using parktool guide).  I'm officially stumped.

Does that make any sense? If so, does anyone have any advice? I can provide a photo if it helps. Any/ all suggestions welcome!

Cheers
T

I do my own work, I am no expert, but I have ideas. Are you using a 8 speed chain? A single speed chain is wider than an 8 speed chain and would probably not shift.
Is the chain the correct length? The Park Tool site has methods by which you can estimate if your chain length is long enough. Duane
Reply
#3
(01-16-2016, 02:05 PM)Old Duane Wrote:  
(01-16-2016, 11:39 AM)Tomtebi Wrote:  Hi all
new to the site; I'm sure this is something that has come up before, but I'm currently trying to do a single-speed to 8x geared conversion, with a downtube shifter.
I've got the dropdown hanger for the rear derailleur bolted into the drop-out (after reading advice from this site...thanks!), and the rear derailleur mounted.

The chain runs through the derailleur and smallest gear (and the front cassette) fine, and I've attached the cable into the derailleur OK. The derailleur adjusts position when I use the shifter, but the chain doesn't move with it. I can manually move the chain onto the biggest sprocket, but not currently using the shifter.  I've tried tightening the cable, but am not 100% sure what the starting position of the shifter should be (I've not found much on Youtube for this) and have double-checked I've routed the cable through the shifter properly (using parktool guide).  I'm officially stumped.

Does that make any sense? If so, does anyone have any advice? I can provide a photo if it helps. Any/ all suggestions welcome!

Cheers
T

I do my own work, I am no expert, but I have ideas. Are you using a 8 speed chain? A single speed chain is wider than an 8 speed chain and would probably not shift.
Is the chain the correct length? The Park Tool site has methods by which you can estimate if your chain length is long enough.  Duane

Hi Duane
I am using an 8 speed chain, and I'm fairly sure it's the right length, but i'll double check. Thanks for the suggestion

T
Reply
#4
(01-16-2016, 02:35 PM)Tomtebi Wrote:  
(01-16-2016, 02:05 PM)Old Duane Wrote:  
(01-16-2016, 11:39 AM)Tomtebi Wrote:  Hi all
new to the site; I'm sure this is something that has come up before, but I'm currently trying to do a single-speed to 8x geared conversion, with a downtube shifter.
I've got the dropdown hanger for the rear derailleur bolted into the drop-out (after reading advice from this site...thanks!), and the rear derailleur mounted.

The chain runs through the derailleur and smallest gear (and the front cassette) fine, and I've attached the cable into the derailleur OK. The derailleur adjusts position when I use the shifter, but the chain doesn't move with it. I can manually move the chain onto the biggest sprocket, but not currently using the shifter.  I've tried tightening the cable, but am not 100% sure what the starting position of the shifter should be (I've not found much on Youtube for this) and have double-checked I've routed the cable through the shifter properly (using parktool guide).  I'm officially stumped.

Does that make any sense? If so, does anyone have any advice? I can provide a photo if it helps. Any/ all suggestions welcome!

Cheers
T

I do my own work, I am no expert, but I have ideas. Are you using a 8 speed chain? A single speed chain is wider than an 8 speed chain and would probably not shift.
Is the chain the correct length? The Park Tool site has methods by which you can estimate if your chain length is long enough.  Duane

Hi Duane
I am using an 8 speed chain, and I'm fairly sure it's the right length, but i'll double check.  Thanks for the suggestion

T

Hopefully one of the Pros will be able to pin down the problem when they notice your post. However, the derailleur cog should be directly in line with each gear. Here is an excellent website that can help with many questions: http://sheldonbrown.com/derailer-adjustment.html Best Wishes, Duane Smile
Reply
#5
Thanks Duane Smile

(01-16-2016, 03:38 PM)Old Duane Wrote:  
(01-16-2016, 02:35 PM)Tomtebi Wrote:  
(01-16-2016, 02:05 PM)Old Duane Wrote:  
(01-16-2016, 11:39 AM)Tomtebi Wrote:  Hi all
new to the site; I'm sure this is something that has come up before, but I'm currently trying to do a single-speed to 8x geared conversion, with a downtube shifter.
I've got the dropdown hanger for the rear derailleur bolted into the drop-out (after reading advice from this site...thanks!), and the rear derailleur mounted.

The chain runs through the derailleur and smallest gear (and the front cassette) fine, and I've attached the cable into the derailleur OK. The derailleur adjusts position when I use the shifter, but the chain doesn't move with it. I can manually move the chain onto the biggest sprocket, but not currently using the shifter.  I've tried tightening the cable, but am not 100% sure what the starting position of the shifter should be (I've not found much on Youtube for this) and have double-checked I've routed the cable through the shifter properly (using parktool guide).  I'm officially stumped.

Does that make any sense? If so, does anyone have any advice? I can provide a photo if it helps. Any/ all suggestions welcome!

Cheers
T

I do my own work, I am no expert, but I have ideas. Are you using a 8 speed chain? A single speed chain is wider than an 8 speed chain and would probably not shift.
Is the chain the correct length? The Park Tool site has methods by which you can estimate if your chain length is long enough.  Duane

Hi Duane
I am using an 8 speed chain, and I'm fairly sure it's the right length, but i'll double check.  Thanks for the suggestion

T

Hopefully one of the Pros will be able to pin down the problem when they notice your post. However, the derailleur cog should be directly in line with each gear. Here is an excellent website that can help with many questions: http://sheldonbrown.com/derailer-adjustment.html    Best Wishes, Duane Smile
Reply


Possibly Related Threads...
Thread Author Replies Views Last Post
  7 speed bike / 5 speed shifter handle 6716 1 2,719 05-23-2016, 08:36 PM
Last Post: DaveM
  STI shifter problem dude 2 3,629 03-01-2016, 08:47 AM
Last Post: dude
  Ultegra 11 speed right hand shifter tx246 4 3,172 07-08-2015, 11:12 AM
Last Post: painkiller
  18 speed right-shifter pod charliebrown 9 3,490 11-21-2014, 02:41 AM
Last Post: painkiller
  Convert down tube shifter to STI shifters with Campag 980 6 x 2 speed JoeHigh 6 3,836 09-08-2014, 08:36 PM
Last Post: nfmisso
  8-speed shifter and derailleur with 7-speed sprocket? smmr89 8 7,544 11-03-2013, 08:18 AM
Last Post: 1FJEF
  6 rear gear with 14 speed shifter ??? hero1900 8 6,332 10-09-2012, 08:04 AM
Last Post: xerxes
  Single speed to 12 speed mynameisamyw 6 6,770 06-05-2012, 11:30 PM
Last Post: xerxes
  Shifters not grabbing after 2nd, problem inside shifter not derailleur/cable tension thedarlington 3 7,000 07-20-2011, 08:19 AM
Last Post: bikesculptor
  21 INCH 12 speed rear problem jacobojajati 3 5,452 07-06-2011, 07:54 AM
Last Post: Joe_W

Forum Jump:



ISSN 1918-3445 © Copyright 2007-2010 Bicycle Tutor / Privacy Policy / Created by Alex Ramon

feed